http://www.blackmoreops.com/2014/09/18/connect-to-wifi-network-from-command-line-in-linux
How many of you failed to connect to WiFi network in Linux? Did you bumped into issues like the followings in different forums, discussion page, blogs? I am sure everyone did at some point. Following list shows just the results from Page 1 of a Google search result with “Unable to connect to WiFi network in Linux” keywords.
Following guide explains how you can connect to a WiFi network in Linux from command Line. This guide will take you through the steps for connecting to a WPA/WPA2 WiFi network.
Before we jump into technical jargons let’s just quickly go over each item at a time.
BTW
Step 1: Find available WiFi adapters – WiFi network from command line
This actually help .. I mean you need to know your WiFi device name
before you go an connect to a WiFi network. So just use the following
command that will list all the connected WiFi adapters in your Linux
machines.
This system has 1 physical WiFi adapters.
Step 2: Check device status – WiFi network from command line
By this time many of you are thinking, why two network devices. The
reason I am using two is because I would like to show how a connected
and disconnected device looks like side by side. Next command will show
you exactly that.
You can check that if the wireless device is up or not using the following command:
Look for the word “UP” inside the brackets in the first line of the output.
In the above example, wlan1 is not UP. Execute the following command to
Step 3: Bring up the WiFi interface – WiFi network from command line
Use the following command to bring up the WiFI interface
If you run the show link command again, you can tell that wlan1 is now UP.
Step 4: Check the connection status – WiFi network from command line
You can check WiFi network connection status from command line using the following command
The above output shows that you are not connected to any network.
Step 5: Scan to find WiFi Network – WiFi network from command line
Scan to find out what WiFi network(s) are detected
The 2 important pieces of information from the above are the SSID and the security protocol (WPA/WPA2 vs WEP). The SSID from the above example is blackMOREOps. The security protocol is RSN, also commonly referred to as WPA2. The security protocol is important because it determines what tool you use to connect to the network.
— following image is a sample only —
Step 6: Generate a wpa/wpa2 configuration file – WiFi network from command line
Now we will generate a configuration file for wpa_supplicant that contains the pre-shared key (“passphrase“) for the WiFi network.
Step 7: Connect to WPA/WPA2 WiFi network – WiFi network from command line
Now that we have the configuration file, we can use it to connect to the WiFi network. We will be using wpa_supplicant to connect. Use the following command
-B means run wpa_supplicant in the background.
-D specifies the wireless driver. wext is the generic driver.
-c specifies the path for the configuration file.
Use the iw command to verify that you are indeed connected to the SSID.
Step 8: Get an IP using dhclient – WiFi network from command line
Until step 7, we’ve spent time connecting to the WiFi network. Now use dhclient to get an IP address by DHCP
Step 9: Test connectivity – WiFi network from command line
Ping Google’s IP to confirm network connection (or you can just browse?)
Thanks for reading.
How many of you failed to connect to WiFi network in Linux? Did you bumped into issues like the followings in different forums, discussion page, blogs? I am sure everyone did at some point. Following list shows just the results from Page 1 of a Google search result with “Unable to connect to WiFi network in Linux” keywords.
- Cannot connect to wifi at home after upgrade to ubuntu 14.04
- Arch Linux not connecting to Wifi anymore
- I can’t connect to my wifi
- Cannot connect to WiFi
- Ubuntu 13.04 can detect wi-fi but can’t connect
- Unable to connect to wireless network ath9k
- Crazy! I can see wireless network but can’t connect
- Unable to connect to Wifi Access point in Debian 7
- Unable to connect Wireless
Following guide explains how you can connect to a WiFi network in Linux from command Line. This guide will take you through the steps for connecting to a WPA/WPA2 WiFi network.
Contents [hide]
- WiFi network from command line – Required tools
- Linux WPA/WPA2/IEEE 802.1X Supplicant
- Step 1: Find available WiFi adapters – WiFi network from command line
- Step 2: Check device status – WiFi network from command line
- Step 3: Bring up the WiFi interface – WiFi network from command line
- Step 4: Check the connection status – WiFi network from command line
- Step 5: Scan to find WiFi Network – WiFi network from command line
- Step 6: Generate a wpa/wpa2 configuration file – WiFi network from command line
- Step 7: Connect to WPA/WPA2 WiFi network – WiFi network from command line
- Step 8: Get an IP using dhclient – WiFi network from command line
- Step 9: Test connectivity – WiFi network from command line
- Summary
- Google+
- Related
WiFi network from command line – Required tools
Following tools are required to connect to WiFi network in Linux from command lineLinux WPA/WPA2/IEEE 802.1X Supplicant
wpa_supplicant is a WPA Supplicant for Linux, BSD, Mac OS X, and Windows with support for WPA and WPA2 (IEEE 802.11i / RSN). It is suitable for both desktop/laptop computers and embedded systems. Supplicant is the IEEE 802.1X/WPA component that is used in the client stations. It implements key negotiation with a WPA Authenticator and it controls the roaming and IEEE 802.11 authentication/association of the wlan driver.iw – Linux Wireless
iw is a new nl80211 based CLI configuration utility for wireless devices. It supports all new drivers that have been added to the kernel recently. The old tool iwconfing, which uses Wireless Extensions interface, is deprecated and it’s strongly recommended to switch to iw and nl80211.ip – ip program in Linux
ip is used to show / manipulate routing, devices, policy routing and tunnels. It is used for enabling/disabling devices and it helps you to find general networking informations. ip was written by Alexey N. Kuznetsov and added in Linux 2.2. Useman ip
to see full help/man page.ping
Good old ping For every ping, there shall be a pong …. ping-pong – ping-pong – ping-pong … that should explain it.BTW
man ping
helps too …
Step 1: Find available WiFi adapters – WiFi network from command line
This actually help .. I mean you need to know your WiFi device name
before you go an connect to a WiFi network. So just use the following
command that will list all the connected WiFi adapters in your Linux
machines.root@kali:~# iw dev phy#1 Interface wlan0 ifindex 4 type managed root@kali:~#Let me explain the output:
This system has 1 physical WiFi adapters.
- Designated name: phy#1
- Device names: wlan0
- Interface Index: 4. Usually as per connected ports (which can be an USB port).
- Type: Managed. Type specifies the operational mode of the wireless devices. managed means the device is a WiFi station or client that connects to an access point.
Step 2: Check device status – WiFi network from command line
By this time many of you are thinking, why two network devices. The
reason I am using two is because I would like to show how a connected
and disconnected device looks like side by side. Next command will show
you exactly that.You can check that if the wireless device is up or not using the following command:
root@kali:~# ip link show wlan0 4: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN mode DORMANT qlen 1000 link/ether 00:60:64:37:4a:30 brd ff:ff:ff:ff:ff:ff root@kali:~#As you can already see, I got once interface (wlan0) as state UP and wlan1 as state DOWN.
Look for the word “UP” inside the brackets in the first line of the output.
In the above example, wlan1 is not UP. Execute the following command to
Step 3: Bring up the WiFi interface – WiFi network from command line
Use the following command to bring up the WiFI interfaceroot@kali:~# ip link set wlan0 up
Note: If you’re using Ubuntu, Linux Mint, CentOS, Fedora etc. use the command with ‘sudo’ prefix
If you run the show link command again, you can tell that wlan1 is now UP.
root@kali:~# ip link show wlan0 4: wlan0:mtu 1500 qdisc mq state UP mode DORMANT qlen 1000 link/ether 00:60:64:37:4a:30 brd ff:ff:ff:ff:ff:ff root@kali:~#
Step 4: Check the connection status – WiFi network from command line
You can check WiFi network connection status from command line using the following commandroot@kali:~# iw wlan0 link Not connected. root@kali:~#
The above output shows that you are not connected to any network.
Step 5: Scan to find WiFi Network – WiFi network from command line
Scan to find out what WiFi network(s) are detectedroot@kali:~# iw wlan0 scan
BSS 9c:97:26:de:12:37 (on wlan0)
TSF: 5311608514951 usec (61d, 11:26:48)
freq: 2462
beacon interval: 100
capability: ESS Privacy ShortSlotTime (0x0411)
signal: -53.00 dBm
last seen: 104 ms ago
Information elements from Probe Response frame:
SSID: blackMOREOps
Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0
DS Parameter set: channel 11
ERP: Barker_Preamble_Mode
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: 16-PTKSA-RC (0x000c)
Extended supported rates: 6.0 9.0 12.0 48.0
---- truncated ----
The 2 important pieces of information from the above are the SSID and the security protocol (WPA/WPA2 vs WEP). The SSID from the above example is blackMOREOps. The security protocol is RSN, also commonly referred to as WPA2. The security protocol is important because it determines what tool you use to connect to the network.
— following image is a sample only —
Step 6: Generate a wpa/wpa2 configuration file – WiFi network from command line
Now we will generate a configuration file for wpa_supplicant that contains the pre-shared key (“passphrase“) for the WiFi network.root@kali:~# wpa_passphrase blackMOREOps >> /etc/wpa_supplicant.conf
abcd1234
root@kali:~#
(where 'abcd1234' was the Network password)
wpa_passphrase uses SSID as a string, that means you need to type in the passphrase for the WiFi network blackMOREOps after you run the command.Note: If you’re using Ubuntu, Linux Mint, CentOS, Fedora etc. use the command with ‘sudo’ prefixwpa_passphrase will create the necessary configuration entries based on your input. Each new network will be added as a new configuration (it wont replace existing configurations) in the configurations file /etc/wpa_supplicant.conf.
root@kali:~# cat /etc/wpa_supplicant.conf # reading passphrase from stdin network={ ssid="blackMOREOps" #psk="abcd1234" psk=42e1cbd0f7fbf3824393920ea41ad6cc8528957a80a404b24b5e4461a31c820c } root@kali:~#
Step 7: Connect to WPA/WPA2 WiFi network – WiFi network from command line
Now that we have the configuration file, we can use it to connect to the WiFi network. We will be using wpa_supplicant to connect. Use the following commandroot@kali:~# wpa_supplicant -B -D wext -i wlan0 -c /etc/wpa_supplicant.conf ioctl[SIOCSIWENCODEEXT]: Invalid argument ioctl[SIOCSIWENCODEEXT]: Invalid argument root@kali:~#Where,
-B means run wpa_supplicant in the background.
-D specifies the wireless driver. wext is the generic driver.
-c specifies the path for the configuration file.
Use the iw command to verify that you are indeed connected to the SSID.
root@kali:~# iw wlan0 link Connected to 9c:97:00:aa:11:33 (on wlan0) SSID: blackMOREOps freq: 2412 RX: 26951 bytes (265 packets) TX: 1400 bytes (14 packets) signal: -51 dBm tx bitrate: 6.5 MBit/s MCS 0 bss flags: short-slot-time dtim period: 0 beacon int: 100
Step 8: Get an IP using dhclient – WiFi network from command line
Until step 7, we’ve spent time connecting to the WiFi network. Now use dhclient to get an IP address by DHCProot@kali:~# dhclient wlan0 Reloading /etc/samba/smb.conf: smbd only. root@kali:~#You can use ip or ifconfig command to verify the IP address assigned by DHCP. The IP address is 10.0.0.4 from below.
root@kali:~# ip addr show wlan0 4: wlan0:Add default routing rule.The last configuration step is to make sure that you have the proper routing rules.mtu 1500 qdisc mq state UP qlen 1000 link/ether 00:60:64:37:4a:30 brd ff:ff:ff:ff:ff:ff inet 10.0.0.4/24 brd 10.0.0.255 scope global wlan0 valid_lft forever preferred_lft forever inet6 fe80::260:64ff:fe37:4a30/64 scope link valid_lft forever preferred_lft forever root@kali:~# (or) root@kali:~# ifconfig wlan0 wlan0 Link encap:Ethernet HWaddr 00:60:64:37:4a:30 inet addr:10.0.0.4 Bcast:10.0.0.255 Mask:255.255.255.0 inet6 addr: fe80::260:64ff:fe37:4a30/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:23868 errors:0 dropped:0 overruns:0 frame:0 TX packets:23502 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:22999066 (21.9 MiB) TX bytes:5776947 (5.5 MiB) root@kali:~#
root@kali:~# ip route show default via 10.0.0.138 dev wlan0 10.0.0.0/24 dev wlan0 proto kernel scope link src 10.0.0.4
Step 9: Test connectivity – WiFi network from command line
Ping Google’s IP to confirm network connection (or you can just browse?)root@kali:~# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_req=3 ttl=42 time=265 ms 64 bytes from 8.8.8.8: icmp_req=4 ttl=42 time=176 ms 64 bytes from 8.8.8.8: icmp_req=5 ttl=42 time=174 ms 64 bytes from 8.8.8.8: icmp_req=6 ttl=42 time=174 ms ^C --- 8.8.8.8 ping statistics --- 6 packets transmitted, 4 received, 33% packet loss, time 5020ms rtt min/avg/max/mdev = 174.353/197.683/265.456/39.134 ms root@kali:~#
Summary
This is a very detailed and long guide. Here is a short summary of all the things you need to do in just few line.root@kali:~# iw dev root@kali:~# ip link set wlan0 up root@kali:~# iw wlan0 scan root@kali:~# wpa_passphrase blackMOREOps >> /etc/wpa_supplicant.conf root@kali:~# wpa_supplicant -i wlan0 -c /etc/wpa_supplicant.conf root@kali:~# iw wlan0 link root@kali:~# dhclient wlan0 root@kali:~# ping 8.8.8.8 (Where wlan0 is wifi adapter and blackMOREOps is SSID) (Add Routing manually) root@kali:~# ip route add default via 10.0.0.138 dev wlan0At the end of it, you should be able to connect to WiFi network. Depending on the Linux distro you are using and how things go, your commands might be slightly different. Edit commands as required to meet your needs.
Thanks for reading.
No comments:
Post a Comment